Sistemul electronic de achiziții publice

1. Specifications Mic Preamp Connector XLR Floating balanced, Pin 2 Hot Mic Preamp Input Impedance ~4.2kΩ Mic Preamp gain 0dB to +60dB Mic Preamp Phantom Power +48VDC, applied to XLR pins 2 and 3 through 6.81kΩ resistors CMRR >40dB, typically 55dB Mic Preamp max input level 0.2Vrms, Gain = 30dB Mic Preamp Equivalent Input Noise (EIN) -125dBu, 22Hz-22kHz, 150Ω source impedance Input Connectors (line) Floating balanced, TIP Hot Input Impedance (line) 10kΩ unbalanced, 20kΩ balanced Max Input (line) >+21dBu, balanced or unbalanced Input Gain Range (line) -15dB to +45 dB Insert Connector 1/4" TRS: Normalled; tip is Send, ring is Return Insert Impedance >5kΩ (ring-return); 100Ω (tip-send) Insert Max Level >+21dBu; >+20dBm (600Ω load-tip) Insert Noise <-84dBu, unweighted (20Hz-20kHz); LINE GAIN Control set to 0dB Insert Distortion <0.01% THD, 20Hz-20kHz, +10dBu Output Connectors 1/4" Balanced/Unbalanced TRS Connectors Output Impedance 100Ω unbalanced, 200Ω balanced Max Output >+21dBu, >+20dBm (600Ω load) Gain Adjustment Range -30dB to +10dB Noise <-80dBu unweighted (20Hz-20kHz); Both Gain Controls set for 0dB, all processing controls OFF Frequency Response 20Hz to 20kHz, +0.5, -0.5dB THD <0.08%THD, 20Hz-20kHz, +10dBu, all Processing Controls OFF Compressor Threshold Range -40dBu to +20dBu Compressor Threshold Characteristic OverEasy® Compressor Ratio >4:1 For input levels beyond 20dB above threshold Max Compression 30dB Compressor Attack Time Program-Dependent; >1s for small level increases, down to 10ms for larage increases Compressor Release Time Program-Dependent; adjustable between approximately 1dB/sec and 75dB/sec Compressor Distortion Typically <0.05%THD, 20Hz-20kHz, 15dB G/R, +10dBu Output, DENSITY @ 0 IMD SMPTE: <0.05%; 60Hz/7kHz 4:1, 15dB G/R, +10dBu Output Level, DENSITY @ 0 De-esser Characteristic Wideband Gain Reduction De-esser Frequency Range 800Hz to 10kHz High Pass, 12dB/octave De-esser Release Time 12dB/octave Program-Dependent; approximately 1mS/dB Enhancer HF Detail Characteristic Program-controlled shelving equalizer, approximately 15dB maximum HF boost Enhancer LF Detail Characteristic Bell-shaped boost @ 80Hz, bell-shaped cut @250Hz, ratio is approximately 2:1 Expander/Gate Threshold Range OFF to +15dBu Expander/Gate Ratio Adjustable 1.5:1 to 10:1 Expander/Gate Max Depth >50dB Expander/Gate Attack Time Program-Dependent, approximately 2mS (at maximum attenuation) Expander/Gate Release Time Program-Dependent, approxiamtely 10mS/dB Expander/Gate Dynamic Range Typically 105dB Power Consumption 15W Operating Voltage DO: 120VAC 60Hz, 100VAC 50/60Hz; EU: 230VAC 50/60Hz Operating Temperature 0°C to 45°C (32°F to 113°F) Dimensions 1.75" x 5.75" x 19" (4.5cm x 14.6cm x 48.5cm) Unit Weight 4.5 lbs/2.04 Kgs Analog cu DBX 286 S

2. Key Features 1. Dual socket R3 (LGA 2011) supports Intel® Xeon® processor E5-2600 v4/v3 family; UPI up to 9.6GT/s 2. Intel® C612 chipset 3. Up to 1TB ECC 3DS LRDIMM; 8x DIMM slots 4. 1x PCI-E 3.0 x16, 2x PCI-E 3.0 x8 5. Intel® i210 Dual GbE LAN ports 6. Integrated IPMI 2.0 and KVM with Dedicated LAN 7. 8x SAS3 (12Gbps) via Broadcom® 3108; HW RAID 0, 1, 5, 6, 10, 50, 60. 8. 6x SATA3 (6Gbps) via C232; RAID 0, 1, 5, 10 9. 740W Redundant Platinum Power Supplies 10. Double power supply Chassis: CSE-825TQ-R740LPB 1 un. Motherboard: X10DRL-C 1 un. CPU: Intel® Xeon® 8C/16T Processor E5-2620 v4 2.10 GHz, 20M Cache 2 un. RAM:16Gb DDR4-2666 ECC REG HDD SATA:8TB 7.2K SATA 6.0 GB/S 256MB 3.5" Enterprise Hard Drive 6 un. SSD (No more than 8 drives including HDDs):240GB, 2.5" SATA 6Gb/s, Enterprise SSD 2 un. (Echivalent KM NETFIRE 6028R-TCR)

3. • Frequency range: 70Hz-16kHz • Frequency response: contoured • Sensitivity: -33.00 dBV/Pa – 22.00 mV/Pa • Self noise: 27dBSPL • Maximum SPL: 120 dB • Cartridge type: electret condenser • Polar pattern: cardioid • Connectivity: 3-pin XLR • Needs phantom power: 11-52 V DC Analog cu Shure CVG12S-B/C Gooseneck Microphone, 30.5cm, Condensator, Cardioid, 3pin XLR male, inkl. Preamp, Mute, LED bottom

4. Specifications : ▪ Supported protocols: ◦ IPv4 hardware switching ◦ IGMP version 2 snooping ◦ IGMP snooping querier ◦ DSCP (IP Type Of Service based priority) ◦ 802.1p (Ethernet 802.1Q tag priority) ◦ HTTP (WEB based management) ▪ 24 Ports Fast Ethernet 10/100MBit/1000MBit/s (AXIA recomandat)

5. Exstreamer 200 | 205 IP Audio decoder with S/PDIF and 2x25W amplified output, mircoSD. Support of Internet Radio (AACplus, MP3, shoutcast, TCP streaming) and VoIP (SIP, RTP) codecs and protocols MAIN FEATURES • G.711, uLaw, aLaw, PCM Encoding • AACplus, MP3, Ogg Vorbis, G.711, PCM linear Decoding • IP Streaming via TCP, UDP, RTP, Multicast • Amplified Output 2x25W (8 Ohm) • RS-232 Serial Port • Power Supply (24V, included) • MicroSD or USB Flash Interface • IR Interface

6. InstreamerMultiprotocol Audio over IP encoder with line level analog input (stereo), serial port, low latency, PCM G.711, G.722 and MP3 encoding MAIN FEATURES • G.711, G.722, PCM linear Encoding • MP3 Encoding (low Latency) • Shoutcast/Icecast Source capability • Audio Level Supervision with SNMP Trap generation • IP Streaming via TCP, UDP, RTP, Multicast • Line Level Input (Stereo) • RS-232 Serial Port • Power Supply (micro USB)

7. xNODE Analog 4X4Analog Line Inputs Input Impedance: >40 k Ohms, balanced Nominal Input Range: Selectable, +4 dBu or -10dBv Input Headroom: 20 dB above nominal inputMeta Analog Line Outputs Output Source Impedance: <50 Ohms balanced Output Load Impedance: 600 Ohms, minimum Nominal Output Level: +4 dBu Maximum Output Level: +24 dBu Frequency Response Any input to any output: +/- 0.5 dB, 20 Hz to 20 kHz Latency Analog Input to Analog Output, 2.75ms including network, converters, and mixing process Dynamic Range Analog Inputs to Analog Outputs 108dB referenced to 0dBFs, 111dB A-weighted Analog Inputs to Digital Outputs 110dB referenced to 0dBFs, 113dB A-weighted Total Harmonic Distortion + Noise Analog Input to Analog Output: < 0.005%, 1 kHz, +18dBu input, +18dBu output Analog Input to Digital Output: < 0.004%, 1 kHz, +18dBu input, -6dBFs output Digital Input to Analog Output: < 0.004%, 1 kHz, -6dBFs input, +18dBu output Crosstalk Isolation, Stereo Separation And CMRR Analog Line channel to channel isolation: 90dB minimum, 20Hz to 20kHz Analog Line stereo separation: 85dB minimum, 20Hz to 20kHz Analog Line Input CMRR: 80dB minimum, 20Hz to 20kHz Power Supply AC Input Auto-ranging supply, 95VAC to 240VAC, 50 Hz to 60 Hz, IEC receptacle, internal fuse Power consumption: 14 Watts I/O connections via industry-standard RJ-45 audio connectors or high-density DB-25 connections, both available prefabricated and ready to attach in seconds. AoIP compatible Livewire+.

8. ANALOG TP-LINK ARCHER MR200 Standards EEE 802.11ac/n/a 2.4 & 5 GHz Transmission speed (WiFi) 802.11 5 GHz: up to 433 Mb/s 2.4GHz: up to 300 Mb/s Operating bands [GHz] 2.4 i 5 Max output power [dBm] 20 Modulation DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM LTE/3G 4G: FDD-LTE B1/B3/B7/B8/B20 (2100/1800/2600/900/800MHz) TDD-LTE B38/B39/B40/B41 (2600/1900/2300/2500MHz) 3G: DC-HSPA+/HSPA+/HSPA/UMTS B1/B8 (2100/900MHz) 4G: FDD-LTE Cat4 (800/900/1800/2100/2600MHz) TDD-LTE (2300/2600MHz) 3G: DC-HSPA+/HSPA+/HSPA/UMTS (900/2100MHz) 2G: EDGE/GPRS/GSM (850/900/1800/1900MHz) Interfaces 4x10/100 Mb/s LAN (1 port LAN/WAN) Antennas 2x integrated (LTE) 3x internal (WiFi) Power 100-240 VAC / 12 VDC